● Independent guides to generators, power stations & home backup power Free generator size calculator →

Whole House Generator Cost (2026): Price and Installation

A line-by-line look at what a standby generator installation costs, and where your money goes.

HomePowerIQ is reader-supported. When you buy through links on our site, we may earn a commission at no extra cost to you. As an Amazon Associate we earn from qualifying purchases. Our picks are based on specs, prices and published data, never on payment. How we make money.

On this page
Blueprint-style cutaway of a two-story house with a standby generator on a pad, gas line and transfer switch feeding the electrical panel

Short answer: most homeowners pay about $8,000 to $16,000 to have a whole house standby generator installed, including the generator. Generac gives that range for its own systems, and cost sites report a wider spread of roughly $5,000 to $25,000 depending on size, fuel and how much work the site needs. The generator is usually less than half the bill; the rest is the transfer switch, pad, fuel line, electrical work, permits and labor.

Below: what each part of the job costs, how size and fuel change the price, the hidden costs that show up in quotes, and how to keep the total down.

Whole house generator price at a glance

SystemTypical installed costWhat you get
Essential-circuit standby (10–14 kW)Low end of the rangeFridge, furnace, lights, sump pump, a few circuits
Mid-size whole house (18–22 kW)About $8,000–$16,000Most of an average home, often including central AC
Large whole house (24 kW and up)About $12,000–$22,000+Whole home with several large appliances
Portable generator plus interlockAbout $1,500–$3,000Manual setup, runs chosen circuits

Ranges come from Generac’s installation guide and national cost surveys (see sources). Your quote depends on your home and local labor rates.

What you pay for, line by line

Cost itemTypical costNotes
GeneratorAbout $4,300–$8,000 (MSRP)Air-cooled 10–26 kW; see our Generac price list
Automatic transfer switchOften included; otherwise roughly $500–$2,800Whole-house (200 A) switches cost more than circuit-level ones
Concrete or composite padA few hundred dollarsSome units ship with a pad
Natural gas lineAbout $400–$1,500+More if the meter or regulator needs an upgrade
Propane tank and lineVaries widelyTank purchase or lease, trenching, line run
Electrical workVariesWire run, panel work, load management modules
Permits and inspectionVaries by cityElectrical, gas and sometimes zoning
Annual maintenanceAbout $200–$600 per yearOil, filters, battery and a service check

A rule of thumb from Generac’s numbers: the generator is roughly a third of the total project, and installation, equipment and materials make up the rest.

What drives the price up

  • Generator size. Going from 14 kW to 24 or 26 kW adds thousands to the equipment cost and often needs heavier wiring.
  • Fuel. An existing natural gas line is usually cheapest. Propane needs a tank big enough for long outages.
  • Distance. The farther the generator sits from the gas meter and electrical panel, the more pipe, wire and labor.
  • Panel and meter upgrades. Older panels or undersized gas meters add cost.
  • Local rules. Setbacks from windows and property lines, noise rules and permit fees vary by town.

How to keep the cost down

  1. Size it right. Use our generator size calculator for a ballpark, then ask the installer for a load calculation.
  2. Ask about load management. It lets a smaller generator start big loads like central AC one at a time.
  3. Get two or three itemized quotes, with the generator, switch, pad, fuel, electrical, permits and warranty listed separately.
  4. Consider an essential-circuit system if you only need the basics.
  5. Compare a portable generator with a panel interlock kit or transfer switch if you are fine starting it yourself.

See Generac installation options →

Is a whole house generator worth it?

It is usually worth it if you lose power often, work from home, rely on a well or sump pump, or have medical equipment that needs power. If outages are rare and short, a portable generator or a portable power station costs far less. A standby generator can also add to resale value in outage-prone areas, but don’t count on recovering the full cost.

Frequently asked questions

How much does a 22 kW whole house generator cost installed?

Generac’s 22 kW with a whole-house switch lists at $6,979 MSRP. Installed, most homeowners land in Generac’s $8,000–$16,000 range depending on the site.

Can I install a whole house generator myself?

In most places, no. The job needs electrical and gas permits and an inspection, and manufacturers generally require an authorized installer for the warranty.

How long does installation take?

The on-site work often takes one to three days, but permits, inspections and equipment lead times can stretch the whole project to several weeks.

Natural gas or propane: which costs less?

If you already have a natural gas line, it is usually cheaper to install and you never refuel. Propane works anywhere but needs a large enough tank for long outages.

What are the ongoing costs?

Plan on roughly $200–$600 a year for maintenance, plus fuel when it runs and a small amount for its weekly self-test.

Sources: Generac backup generator installation guide; Angi generator installation costs; HomeYou generator installation cost; ThePricer standby generator cost. Checked November 2026.

Charles Grover

Charles Grover writes HomePowerIQ’s guides to generators, portable power stations and home backup power. He compares models using manufacturers’ published specs, independent data and current prices, with a focus on sizing backup power correctly and connecting it safely.